SID player (synthesizer) with the ability to save music in different audio formats.
Version 1.2 - volume bug fixed. Version 1.1 - added fast forward button, new shortcuts added. Version 1.0 - first release, support for PSID files only.
You need to load presets into the plugin. To load a file, click on the information line.
Controls: Gain - input level knob Bass - tone knob Middle - tone knob Treble - tone knob Power Amp - power amp level knob (level stabilized input/output) Low End - tone knob (resonance) Presence - tone knob Volume - output level knob Stereo - mono or stereo switch
Here is some information [RUS] on how to make presets: guitar-gear.ru
Version 5.0 - switchable oversampling up to 32x. Version 4.0 - improved poweramp. Version 3.1 - tube stage bug fixed. Version 3.0 - improved tube stage. Version 2.0 - new tonestack type is added. Version 1.1 - save preset bug fixed. Version 1.0 - first release.
2120 is Peavey 5150 style 230 is Engl 530 style Barbarian is Engl Savage style Bass is Ampeg SVT style Citrus CR120 is Orange OR120 style Crunchman is Friedman BE-100 style Dark II is Mesa Mark II C+ style Firecube is Engl Fireball style Four is Diezel VH4 style Gerbert III is Diezel Herbert CH-3 style Hell is Randall Satan style Himatt 20 is Hiwatt Custom 20 style Hot Dog is BadCat Hot Cat style J800 is Marshall JCM800 style J800 Lead is Marshall JCM800 Lead Series style K700 is Marshall JCM800 mod by NaLex Ketchup is Tomato style Magic is Crate BV style Pectifier is Mesa Rectifier style Power Amp Revolt is Krank Revolution style Screamer is NaLex Tube Screamer Steves is Friedman SS-100 style SV is Carvin Legacy style Triad is Groove Tubes Trio style Twin Clean is Fender Twin style Uber is Bogner Ubershall style ZLO is Soldano SLO style
-------------------------------------------------------- Old versions
Capacity meter with automatic selection of the measurement range. It measures the charging and discharging times of the capacitor, and converts the measured values into capacitance.
The measured capacity is from 10pF to 10mF (10000uF).
A one-time meter calibration is required. For calibration, you need to turn on the meter with the calibration button pressed. Then connect the reference capacitors, the value of which is indicated on the display. The connection of each capacitor must be confirmed by pressing the calibration button. The values of the reference capacitors can be changed in the "set calibration caps" section.
Information is output to an external display and to a serial port. Customize the code for the display you are using.
Warning! The capacitor must be completely discharged before measurement. Otherwise, the device may be damaged.
Version 2.0 - added calibration. Version 1.0 - first release.
Instructions for using the plugins. Assemble the sequence: Ratio Generator, Compressor, Ratio Meter. On the Ratio Meter, press Reset. On the Ratio Generator, press Start. After stopping the generator, use the cursors to measure the ratio and threshold of the compressor.
Note: After this amp simulator, you need to put the cabinet simulator (IR).
Controls: Input - input level switch Gain - input level knob Ultra Low - tone switch Ultra High - tone switch Bass - tone knob Midrange - tone knob Frequency - midrange frequency knob (works like a five-position switch) Treble - tone knob Master - output level knob Stereo - mono or stereo switch
Oversampling 8x.
Version 1.1 - tonestack correction. Version 1.0 - first release.
Controls: Threshold (knob) - compression threshold; Make Up (knob) - output gain; Attack (knob) - envelope attack time; Release (knob) - envelope release (recovery) time; Ratio (knob) - signal reduction level above the threshold; HP SC (switch) - high pass filter (100 Hz) of side chain; GR - gain reduction indicators; Output (switch) - overload protection type, clipper or limiter at 0 dB (overload indicators are located at the edges); Separate Control (switch) - separate control of the left and right channels; Stereo (switch) - mono or stereo input;
Version 3.1 - oversampling up to 32x. Version 3.0 - oversampling 4x is added. Version 2.0 - Ratio knob is added. Version 1.0 - first release.
Noise Katana VST & AU (V1.0) - Dynamic Noise Suppressor.
Controls: Sensitivity - sensitivity knob Stereo - mono or stereo switch (in the upper left corner)
Instructions for using the plugin. Set the Sensitivity knob to maximum (far right) and decrease the sensitivity until you stop hearing noise during pauses. If noise is also heard in the desired signal, then you need to further reduce the sensitivity of the noise suppressor.
This is a plugin for removing clicks from audio recording. For example, when joining two segments. For the plugin to work, you need to load a text file with the times on which the clicks occur. To load a file, click on the information line.
An example of setting the time in a file:
# comment # minutes, seconds # time 1 0, 32.52 # time 2 1, 24.235 end